Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 5931 visitantes online.
Productos
Información
Destacado
Inicio >> VESTEL >> 11AK20 Manual de Servicio
 
 0 artículo(s) en Su carrito 

VESTEL 11AK20
Manual de Servicio


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Contiene diagramas del circuito
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del VESTEL 11AK20 Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo general contienen diagramas de circuitos, tarjetas de circuitos impresos, consejos para reparación, diagramas de cableado, diagramas de bloque y lista de refacciones. El Manual de Servicio (a veces llamado Manual de Reparación) es usado principalmente por los técnicos.

Si tan solo quiere saber cómo utilizar su televisión, reproductor de vídeo, reproductor de mp3, etc. Quizá lo que necesita es el Manual del Propietario. Después de colocar la orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages:

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
7. POWER SUPPLY (SMPS) : The DC voltage sources required at various stages of the chassis are provided by an SMPS controlled by the IC801 (MC44603 for common models and MC44604 for �low power consumption on stand by mode� models). This IC is designed for driving, controlling and protecting the switching MOSFET transistor of SMPS (Q801). This supply has three outputs; one 112V output which is used for horizontal output and 33V generation needed by tuner section, one 16V output for all small signal sections an uC and one for audio output section. This chassis may be used in 90 - 270 volt with appropriate optional circuitry and components. The uC which is supplied by a source designed regulator with zener diode (D814) controls stand by mode by switching Q803 (for 44604 application Q806). 8. uC (MICROCONTROLLER) : The microcontroller hardware that is member of the ST6 family has a TV receiver control software with menu control. It controls the chassis through IIC bus, PWM outputs and I/O ports. Dominant features of controller are control of optional teletext, outputs for OSD, IR control signal receiving, and internal EEPROM. The controller has IIC communication port at # 40 , # 41 and OSD driver (R,G,B,FBl) at # 22, # 23, # 24, # 25. PWM control outputs are tuning # 34; vertical linearity adjustment # 1; AGC adjustment # 2. Other control outputs are Muting - video ident # 3; led driver # 4; system switches # 5, # 6, # 8, # 19, # 20, # 36; tuner switches # 18, # 19 and inputs are AFC information from IF # 9; keyboard # 10, # 11, # 13, # 14; scart mode ident (4/3-16-9) # 38, # 39; horizontal sync # 26; vertical # 27; infrared # 35 and reset # 33. The uC starts system according to option diodes configuration (D501, D503, D505, D506, D508). The controller has also a software which is able to control some service adjustments: R,G,B gain; R,G cut off; vertical position; vertical linearity; horizontal position; vertical amplitude; AGC; language selection for teletext. For enter to service mode followed procedure must be act within four seconds: 1Press volume down button on the keyboard; 2Press �prog� button on the R/C hand set; 3Press �- -� button on the R/C hand set; 4Press �TV �� button on the R/C hand set; Parameters can be sellected by program up and down, parameter adjustments can be done by volume up and down buttons. Memorizing the adjusted parameters can be done by pressing red button. For exit from service mode Press � TV �� button. 9. TELETEXT : The video signal coming from IF stage is fed to Data Slicer IC001. Then, there are two possibilities for decoding part; CF70095 or CF70195 for 1-Page simple text applications and CF7020X family for fastext and toptext applications. Finally, R, G, B and FBL signals are sent to the related inputs of STV2118. The alignment procedure for CF70095 or CF70195 application is as following: 1Apply a video with teletext transmission and select for teletext. 2Adjust the coil (VL001) for the voltage at pin # 28 2.5V. 10. CRT BASE-BOARD : When RGB signals enter the input of the video amplifier stage (CRT base-board), they are amplified by means of three symmetrical video amplifier stages. For this purpose three 2SC2482 high voltage, video output transistors are used. So, high gain-bandwidth product is achieved. Furthermore black level changes at the output amplifiers caused by temperature or component agings are compensated by means of a closed loop control system. For this reason the cathode current information (ICAT) is sent to STV2118.

5

Quizás también quiera comprar

$4.99

SX-K700 TECHNICS
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …

$4.99

CJ-V51 PIONEER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

GRAND PRIX ELECTRONIC 754 BECKER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

SX-PR602 TECHNICS
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

EV-S1000E SONY
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …

$4.99

GRAND PRIX ELECTRONIC 780 BECKER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

AG7330 PANASONIC
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

EVO-9850 VOLUME 1 SONY
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…
>
Parse Time: 0.211 - Number of Queries: 125 - Query Time: 0.057